Resetting the heater is one of the most basic repairing steps in most heaters and it’s one of the easiest jobs as well. But if you are not sure about the reset button location, this job can make your day complicated.
So, where is the Atmor water heater reset button, and how to use it?
In the Atmor tankless water heaters, there are three reset buttons inside the control panel which are located on the side and top of the heating elements. In Atmor instant water heaters, the single reset button is located outside the heater. Pressing those buttons reset the system.
While troubleshooting any Atmor tankless water heater, I have often noticed that resetting the heater does the job. But not all models have a reset button. Give this article a read and you will know how to find the buttons and use them in detail.
Table of Contents
Atmor Water Heater Reset Button Location
Atmore has both tankless and with-tank water heaters. They have reset buttons in different locations depending on the model of the heater. Here are the locations of those tanked and tankless Atmor water heaters.
01. Atmor Tankless Water Heater Reset Button Location
In an Atmor tankless water heater, there are three reset buttons. However, not all Atmor tankless water heaters have reset buttons. Only the ThermoPro and ThermoPro 2 series of Atmor tankless water heaters come with those reset buttons.
In these water heaters, there are 3 reset buttons which are located on the control panel. When you remove the cover of your tankless water heater, you will notice two heating elements. The first reset button will be on the upper left side of the left heating element. And the other two reset buttons will be on the top of each heating element.
Here is a picture of the heating element locations for better understanding.
The buttons are red in color and round shaped so it will be easier for you to identify them. Due to wiring, it might be a little difficult for you to find the reset buttons located at the top of the
heating elements. But if you look carefully behind the wiring, you will find them.
02. Atmor Instant Water Heater Reset Button Location
If you are a user of Atmor instant water heater 100 Series, you will get 1 reset button in the water heater. In these water heaters, the reset button is located outside the unit. So, it’s easier to find and use it.
In these water heaters, there are two knobs and between those two knobs, there are three buttons on the upper cover. Those three buttons are called B, C, and D. The C button or the middle button is the reset button which is in the middle of the test and pump buttons.
In the next segment, I will discuss how to use these reset buttons to reset the Atmor water heater.
How To Reset The Atmor Water Heater? – Tankless Models
Due to overheating, high water pressure, or any other electrical issue, the reset button of your Atmor tankless water heater can get tripped. In these cases, you need to reset the unit in order to get hot water again.
Follow the resetting process mentioned below to reset your Atmor tankless water heater.
Step 1: Ensure Safety
The resetting process involved opening the front cover and handling the wirings inside the heater. Also, according to the Atmor ThermoPro Series Manual, it is very important to make sure, no electrical power is reaching the unit.
So, before you start the resetting process, make sure your circuit breaker is OFF to avoid any electrical accidents. Also, after turning the power off, give your heater some time to cool off before touching it.
Step 2: Remove the Cover
As the reset buttons in this water heater are located inside the cover, you have to remove the cover to access them. On the sides of the water heater, you’ll find two bolts on each side. Use an adjustable wrench to remove them. Once the bolts are removed, carefully take off the cover.
Step 3: Locate the Reset Buttons
The Atmor tankless water heaters have three reset buttons. You have to locate all three. The location of these reset buttons is mentioned above in detail.
Step 4: Reset the Water Heater
Once you have found all the buttons, it’s time to reset the heater. To reset your ATmor tankless water heater, start by pressing the red reset button located on the side.
Next, press the two red reset buttons one by one on the top of the heating elements. I always find these two buttons a bit tricky to reach. You need nimble fingers to reach them.
When you press these buttons, listen for a “click” sound. This sound indicates that the reset has been successful.
Step 4: Reassemble the Heater
Now that you are done with resetting the heater, you have to reassemble the heater. Install the cover of the heater to its position and secure it tightly with the bolts.
Step 5: Turn on the Hot Water
Once the heater is all set to its original position, you can turn back the power to the heater. And also turn the heater On. now check if the heater works properly or not.
How To Reset The Atmor Water Heater? – Instant Models
The resetting process of Atmor instant water heaters including the Atmor 100 series is different from the resetting process of the tankless heaters. Here’s how to reset an Atmor instant water heater.
When you have done any maintenance to your Atmor instant water heater or there has been a power cut-off, the heater will shut itself down and will remain in this position until you reset it. Resetting these water heaters is very simple.
You just have to press the “Reset” or “C” button on your Atmor instant water heater. And the unit will reset itself and go back to its regular function.
FAQs:
Why would a tankless water heater need to be reset?
When your tankless water heater can’t supply sufficient hot water or stops working, it might be overloaded or affected by a power outage. In such cases, you may need to reset the water heater to make it function properly again.
How long do I have to hold the reset button on the water heater?
How long to hold the reset button on the water heater depends on the model of the heater. In most cases, heaters have only one reset button and you have to hold it for 3-5 seconds. In Atmor, you don’t have to hold the button after pressing it.
What happens when you press reset on a water heater?
The reset on a water heater is a safety device that shuts off when there is any power or water overload on the system. When you press reset, this feature restores the hot water and helps it resume its regular function.
Is it safe to reset a water heater?
Yes, it’s safe to reset a water heater yourself as long as you turn off the power first. If you try it with the power on, it is risky. However, you don’t need a technician for this basic procedure, but safety precautions are important.
Does my heater have a reset button?
If you are an Atmor tankless water heater ThermoPro or ThermoPro 2 user, your heater will have reset buttons. If you are a user of an Atmor 100 series instant heater, there will be a reset button as well. For other models, you won’t have a reset button.
Conclusion:
Here goes everything you had to know about the Atmor water heater reset button. I hope after reading this article you could easily find out those buttons and the resetting process was all easier.
Always make sure to take safety measures like turning off the power to the heater before doing such things.
Let’s end today’s discussion here. Have a great day!
Also, read our article on the Atmor water heater troubleshooting guide.